829 Sheridan Drive :: Tonawanda, NY 14150
(716) 874-6900 Phone :: (716) 874-6966 Fax
bought truck with 130,00mi immediate problems with dying, troubleshot to pmd ordered replaced now 200,000+mi and still running smooth.
...read more
From: juan h.
Fast shipping and awesome tech support. Fast response to questions I had on the product. Would/will buy from these guys again!
...read more
From: ben l.
Follow Us on Facebook

6.5TD C/K Trucks  >  Turbochargers & Parts  >  New Aftermarket GM4/GM8 Turbo

New Aftermarket GM-8 turbocharger which also is an upgrade for a GM-4. For all 94+ C/K trucks, subs and Tahoes.

New Aftermarket GM4/GM8 Turbo

New Aftermarket GM4/GM8 Turbo

Model: ssd-2988D $699.99 $649.99
United States and Canada - All Deliveries to the United States and Canada will be made by UPS. You will be quoted the shipping cost and presented with delivery options at the time of checkout. See our shipping calculator for more information.
International Customers - Review Shipping Policies
NOTICE:
This item does not qualify for the free shipping promotion on orders over $200.00
Check Out

New Aftermarket GM-8 Turbocharger. For all 1994 and newer C/K trucks, subs and tahoes. A direct fit for all 1996+ GM-8 turbos, or use as an upgrade to the GM-4 on your 94-95. Will not fit Vans or H1 Hummers.

Finally an affordable replacement turbo for your Chevy GMC C/K pick-up.  It is warranted for one year. Complete with wastegate and wastegate actuator.

Symptoms of low or no boost are sluggish acceleration, heavy smoke on acceleration, poor mileage, and loss of bost pressure (if you have a boost gauge)

Before purchasing, check your vacuum pump, vacuum lines and wastegate solenoid (located on the drivers side valve cover) for proper operation, as they control the wastegate which directly affects boost. If all ok, then your turbo is bad.

NO CORE DEPOSIT REQUIRED

NOTES:

*Requires additional shipping when shipping to outside the USA.

*This unit is a high quality import. If you prefer one made in the USA, please see our ssd-GM4 and/or ssd-GM8 turbos also in this category.

*Gaskets and studs if needed are sold separately in this category

*This aftermarket turbo uses Wicked Wheel p/n ssd-WW65A if more hp is desired.

*May not work with those spring boost gadgets sold (ex. tubomaster) which we strongly advise against using anyways.

IN STOCK, READY TO SHIP!

WARNING!! CHANGE ENGINE OIL PRIOR TO TURBOCHARGER INSTALLATION. NOT DOING SO MAY RESULT IN PREMATURE TURBOCHARGER FAILURE.

TURBOCHARGER INSTALLATION INSTRUCTIONS INSPECT – LINES AND FITTINGS

  1. Visually inspect the oil supply and drain lines for kinks, clogging, or other restrictions.
  2. Check exhaust manifold, oil supply, and oil drain line flanges for cracks or rust. Verify flatness on surface areas. Remove any old gaskets or any gasket material present on these surface areas.
  3. Check air cleaner; air cleaner duct; and the exhaust manifold for any foreign objects.

ANY FOREIGN OBJECTS LEFT IN THESE AREAS CAN FATALLY DAMAGE THE TURBOCHARGER AND MAY CAUSE DAMAGE TO THE ENGINE! INSPECT AND PREP– NEW TURBOCHARGER

  1. Ensure that no dirt or foreign objects have entered the turbocharger openings.
  2. Place new o-ring and gaskets on oil inlet side of turbo, use clean engine oil to lubricate o-rings before assembly.

TURBOCHARGER INSTALLATION

  1. Install turbocharger, mount both rear and front side, using high temperature nickel anti-seize lubricant to the bolt threads.
  2. Position all wire retainers and install bolts.
  3. Lubricate turbocharger by pouring clean engine oil into the oil inlet hole of the turbo. With your fingers, spin the compressor wheel several times to coat the turbocharger bearings with oil. Pour more oil into the oil inlet hole to top it off. There may be some drainage, but this is of no concern.
  4. Connect the oil supply line, position the oil feed tube and install oil inlet bolts.
  5. Connect the air cooler duct inlet, installed with v-band clamp.
  6. Connect the air exhaust duct, installed with v-band clamp.
  7. Check for proper crankcase oil level.
  8. Test to prevent “engine start – fuel shut off”: crank the engine for a short duration of 15 seconds until the gauge shows an oil pressure build up.
  9. Start the engine and let it idle for 5-10 minutes. (Do not rev the engine during this time)
  10. Inspect installation for any oil leaks.

 

New Aftermarket GM4/GM8 Turbo

 

Click to Load this Photo Click to Load this Photo Click to Load this Photo
Click to Load this Photo Click to Load this Photo
Visa, MasterCard, Discover, American Express and e-Check, processed by PayPalVerified by PayPal
SSDieselSupply.com - © Copyright 2004-Present
36,921,616 visits since 7/17/2004

Website Development and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company