829 Sheridan Drive :: Tonawanda, NY 14150
(716) 874-6900 Phone :: (716) 874-6966 Fax
Update== The Truck Runs. Just got done installing the ssd-006 kit took me a hole 7 min. start to finish. Looks good under the hood also. delivery time was great got it in 3 days. Started the truck up and it sounds like it did when it was new.No more...
...read more
From: Paul S.
I bought a 96 suburban w/90k on it. the IP went bad at 99k, had it warrantied by the dealer and new about the remote PMD/FSD being better in the long run. Well without it my long run was 24k before the PMD failed with the family in the truck going on A...
...read more
From: Donald P.
Follow Us on Facebook

6.5TD C/K Trucks  >  ECONOMY SERIES PMDs, Heat Syncs and Resistors  >  6.5TD ECONOMY SERIES FSD Heat-Sync II kit for C/K Trucks (includes PMD and resistor)

SSDiesel Economy Series FSD Heat-Sync II kit for 1994-2002 C/K Trucks...Solves your PMD failure issues at a price you can afford

6.5TD ECONOMY SERIES FSD Heat-Sync II kit for C/K Trucks (includes PMD and resistor)

6.5TD ECONOMY SERIES FSD Heat-Sync II kit for C/K Trucks (includes PMD and resistor)

Model: ssd-077 $225.00
United States and Canada - All Deliveries to the United States and Canada will be made by UPS. You will be quoted the shipping cost and presented with delivery options at the time of checkout. See our shipping calculator for more information.
International Customers - Review Shipping Policies
Check Out

Brand new Ecomomy Series FSD Heat-Sync IITM kit, for all GM 6.5 Turbo Diesels with electronic fuel injection used in C/K trucks and Suburbans from 1994-2002. Solves the problem of frequent PMD failure with your GM Diesel at an affordable price.

The PMD (pump mounted driver) is that small black box mounted on the side of your injection pump. It is a signal amplifier that powers the fuel solenoid. It contains 2-500 watt transistors which create a lot of heat. The factory mistakenly mounted this PMD module on the side of an already hot injection pump and in the engine valley below the intake manifold where temperatures skyrocket. As everyone knows, electronics do not like heat and they will fail prematurely. Symptoms of failure are stalling, hard starting, surging, poor fuel mileage, erratic idle/throttle and finally no-start. When they go it usually will not give any codes with the SES (Service Engine Soon) light. This Cooler kit, relocates the PMD to a cooler area of the engine compartment, above the intake, on a massive oversized heat sink. A proven design. Our design has some distinct advantages over all the competition\'s. Please check our "advantages" section on our homepage and our FAQ section for details.

This kit includes everything needed including a new Economy Series PMD, FSD Heat Sync II cooler as pictured, and a stock calibration resistor. Detailed step-by-step instructions also included. No drilling or cable splicing. A truely simple Plug-and-play installation. Professionally engineered and manufactured. Only basic hand tools required.  Removal of the top shroud required. Approximately a 10-20 minute installation. See our warranty page for more info.

***WORD OF CAUTION*** Heat Transfer Technology is a science. The sizing of a heat sink requires calculations for the heat sink load of 2-500 watt transistors in an underhood environment exceeding 150DF. The mass of the heat sink, cooling fin design and cooling fin surface area are CRITICAL to PMD life. Although our "FSD Heat-Sync II" runs significantly cooler then most of the competitors, most others will still somewhat do the job. However, I see one out there with little to no "home made fins" that can\'t possibly dissipate the heat of 2-500 watt transistors. Temperature will fry your PMD again in short order. Look to buy the best functioning one, not the prettiest one. Extensive research and engineering have gone into my design. No guesswork involved!


Calibration resistor comes pre-installed in the harness connector. 

This is a lighter duty imported version of our famed "made in USA" ssd-006 Premium HD FSD Heat Sync

If replacing a Stanadyne "GRAY" unit (made in Malaysia) with our new advanced technology PMD, you will either need to purchase a ssd-9908B adapter harness, or simply file off the "ears" on your gray end harness for a perfect fit.



6.5TD ECONOMY SERIES FSD Heat-Sync II kit for C/K Trucks (includes PMD and resistor)


Click to Load this Photo Click to Load this Photo Click to Load this Photo
Click to Load this Photo Click to Load this Photo Click to Load this Photo
Visa, MasterCard, Discover, American Express and e-Check, processed by PayPalVerified by PayPal
SSDieselSupply.com - © Copyright 2004-Present
38,860,479 visits since 7/17/2004

Website Development and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company