829 Sheridan Drive :: Tonawanda, NY 14150
(716) 874-6900 Phone :: (716) 874-6966 Fax
I ordered the PMD because My 96 was doing all of the stalling,fish biting the internet talks about. The instructions were clear, but I found I needed some extra tools, I used long 18"inch blade screw driver, went in under the rad hose from the front and...
...read more
From: Clive M.
I had just purchased a gmc suburban and the day I went to pick it up the service engine light came on(code 35). The truck was very hard to start, trying to stall at idle and bucking going down the road. Needless to say I was very disapointed, almost to...
...read more
From: Ferman G.
Follow Us on Facebook

6.5TD C/K Trucks  >  ECONOMY SERIES PMDs, Heat Syncs and Resistors  >  6.5 Diesel ECONOMY SERIES FSD Heat-Sync II (no PMD or resistor)

SSDiesel Supply ECONOMY SERIES FSD Heat-Sync IITM (less PMD and Resistor)

6.5 Diesel ECONOMY SERIES FSD Heat-Sync II (no PMD or resistor)

6.5 Diesel ECONOMY SERIES FSD Heat-Sync II (no PMD or resistor)

Model: ssd-067 $59.99 $39.99
United States and Canada - All Deliveries to the United States and Canada will be made by UPS. You will be quoted the shipping cost and presented with delivery options at the time of checkout. See our shipping calculator for more information.
International Customers - Review Shipping Policies
Check Out


Brand new ECONOMY SERIES FSD Heat-Sync IITM (less PMD and resistor) for all GM 6.5 Turbo Diesels with electronic fuel injection in C/K pick-ups and Suburbans, 1994-2000. Manufactured in USA by SSDiesel SupplyTM, GM 6.5 TD specialists. Solves the problem of frequent PMD failure with your GM Diesel.

The PMD (pump mounted driver) or FSD (fuel solenoid driver) is that small black box mounted on the side of your injection pump. It is a signal amplifier that powers the fuel solenoid. It contains 2-500 watt transistors which create a lot of heat. The factory mistakenly mounted this PMD module on the side of an already hot injection pump and in the engine valley below the intake manifold where temperatures skyrocket. As everyone knows, electronics do not like heat and they will fail prematurely. Symptoms of failure are stalling, hard starting, surging, poor fuel mileage, erratic idle and finally no-start. When they go it usually will not give any codes with the SES (Service Engine Soon) light. This American Made Cooler, relocates the PMD to a cooler area of the engine compartment, above the intake, on a massive heat sink. A proven design. Our design solves the flaws in all other cooler designs, including the one without fins. Please check out our "FSD advantages" page on the toolbar of our home page, also the FAQ section.

Includes everything EXCEPT a new PMD and resistor to complete the installation. (shown for reference in photo only) We can supply a new Stanadyne PMD and resistor if needed, please see other versions on the products page which include the PMD. Included is 1) cooler as pictured, grade 8 mounting hardware (required to obtain proper torque for heat transfer), and our SILICONE Heat transfer pad, proven far superior then any other made. The original harness will plug right into the module with no modification or strain on wires. Detailed step-by-step installation instructions included. Removal of the top shroud required. Only basic hand tools required. No drilling or cable splicing. Professionally engineered and manufactured in USA by SSDiesel SupplyTM. Properly sized for the heat load!

***WORD OF CAUTION*** Heat Transfer technology is a science. The sizing of a heat sink requires calculations for the heat load of 2-500 watt transistors in an underhood environment exceeding 150 DF. The mass of the heat sink, cooling fin design and cooling fin surface area is CRITICAL to PMD life. Although our "Heat-Sync" runs significantly cooler then most of the competitors, most others will still somewhat do the job. However, I see one out there with little to no "home-made fins" that couldn't possibly dissipate the heat of 2-500 watt transistors. Temperature will fry a PMD. Look to buy the best fuctioning one, not the prettiest one. Extensive reasearch and engineering have gone into my design. No guesswork involved.

If relocating your existing PMD make sure first it is worthy to do so. If it has over 30K miles on it or has ever shown signs of failure, leave it be and install a new PMD on the FSD Heat Sync II. We sell them complete with PMD and resistor as p/n ssd-077. A FSD Heat Sync II will not fix an already bad PMD, just prevent future damage. Please contact tech support for information if planning to re-use your old PMD.

Included in the box: 1) ECONOMY SERIES FSD Heat Sync II, 4) PMD grade 8 mounting screws, 1) silicone heat transfer pad and detailed instructions.

NOTE: This is a lighter duty version of our patented ssd-005 FSD Heat Sync

PMD NOT included, shown for reference only.

6.5 Diesel ECONOMY SERIES FSD Heat-Sync II (no PMD or resistor)


Click to Load this Photo Click to Load this Photo Click to Load this Photo
Click to Load this Photo Click to Load this Photo Click to Load this Photo
Visa, MasterCard, Discover, American Express and e-Check, processed by PayPalVerified by PayPal
SSDieselSupply.com - © Copyright 2004-Present
38,860,607 visits since 7/17/2004

Website Development and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company