829 Sheridan Drive :: Tonawanda, NY 14150
(716) 874-6900 Phone :: (716) 874-6966 Fax
I just wanted to say that WALT is THE MAN! I called numerous dealerships, diesel repair facilitys etc.....and Walt is the only one who could help me without costing me an arm and a leg! I didn't buy any parts due to the time I had to deliver a used diesel...
...read more
From: Wayne
I just purchased a 1998 GMC Sierra 2500 SLT extended cab 8ft bed 4wd from craigslist. The guy stated it wasn't running because it needed a MAP sensor. The guy wanted $500. I gave himn $400. I took Walt's PMD off my other truck and installed it on...
...read more
From: Phil P.
Follow Us on Facebook

Sprinter Diesel  >  Turbochargers & Components  >  New Sprinter Turbo 3.0L 2007-2009

New Sprinter Turbo 3.0L 2007-2009

  • Four stage balanced process
  • Full high-speed balanced
  • New Manufactured in the USA

New Sprinter Turbo 3.0L 2007-2009

New Sprinter Turbo 3.0L 2007-2009

Model: ssd-0111N $1,232.30
United States and Canada - All Deliveries to the United States and Canada will be made by UPS. You will be quoted the shipping cost and presented with delivery options at the time of checkout. See our shipping calculator for more information.
International Customers - Review Shipping Policies
Check Out

 

New Sprinter Turbo 3.0L 2007-2009

New Sprinter turbochargers Manufactured by Rotomaster for Sprinter 3.0L applications.

Applications: 2007 to 2009 Dodge Sprinter 3.0L
2007 to 2009 Freightliner Sprinter 3.0L
2007 to 2009 Mercedes Sprinter 3.0L OM647
2007 Jeep Grand Cherokee 3.0L OM642
Reference Numbers: 761154-5007, 761154-0004

No core deposit required

Please follow all manufactures installation instructions. Professional installation may be required.

WARNING!! CHANGE ENGINE OIL PRIOR TO TURBOCHARGER INSTALLATION. NOT DOING SO MAY RESULT IN PREMATURE TURBOCHARGER FAILURE.

TURBOCHARGER INSTALLATION INSTRUCTIONS INSPECT – LINES AND FITTINGS

  1. Visually inspect the oil supply and drain lines for kinks, clogging, or other restrictions.
  2. Check exhaust manifold, oil supply, and oil drain line flanges for cracks or rust. Verify flatness on surface areas. Remove any old gaskets or any gasket material present on these surface areas.
  3. Check air cleaner; air cleaner duct; and the exhaust manifold for any foreign objects.

ANY FOREIGN OBJECTS LEFT IN THESE AREAS CAN FATALLY DAMAGE THE TURBOCHARGER AND MAY CAUSE DAMAGE TO THE ENGINE! INSPECT AND PREP– NEW TURBOCHARGER

  1. Ensure that no dirt or foreign objects have entered the turbocharger openings.
  2. Place new o-ring and gaskets on oil inlet side of turbo, use clean engine oil to lubricate o-rings before assembly.

TURBOCHARGER INSTALLATION

  1. Install turbocharger, mount both rear and front side, using high temperature nickel anti-seize lubricant to the bolt threads.
  2. Position all wire retainers and install bolts.
  3. Lubricate turbocharger by pouring clean engine oil into the oil inlet hole of the turbo. With your fingers, spin the compressor wheel several times to coat the turbocharger bearings with oil. Pour more oil into the oil inlet hole to top it off. There may be some drainage, but this is of no concern.
  4. Connect the oil supply line, position the oil feed tube and install oil inlet bolts.
  5. Connect the air cooler duct inlet, installed with v-band clamp.
  6. Connect the air exhaust duct, installed with v-band clamp.
  7. Check for proper crankcase oil level.
  8. Test to prevent “engine start – fuel shut off”: crank the engine for a short duration of 15 seconds until the gauge shows an oil pressure build up.
  9. Start the engine and let it idle for 5-10 minutes. (Do not rev the engine during this time)
  10. Inspect installation for any oil leaks.
New Sprinter Turbo 3.0L 2007-2009

 

Visa, MasterCard, Discover, American Express and e-Check, processed by PayPalVerified by PayPal
SSDieselSupply.com - © Copyright 2004-Present
36,921,755 visits since 7/17/2004

Website Development and Web Hosting by Online Media
Online Media - Buffalo's Web Hosting Company